All About Handyman Services Daily

A Step-by-Step Guide of Drywall Finish Levels

Aug 26

There are many factors that affect the quality of finished drywall. Both the framing job as well as the overall care during drywall Denver installation will determine the final results. Once these steps have been completed successfully, the final challenge is to finish the job to your satisfaction. This is important to note that even though a wall acts as a separator, it must be finished properly. There are five levels of drywall finishing. Each one is designed to meet different needs. Let's take a look at them.

Level 0.

This is temporary construction and therefore does not require any drywall tape or finishing. If you aren't sure what your drywall finish will be, Level 0 is an option.

Level 1

Level 1 is used by drywall contractors in attics, garages, and other areas that are not accessible to the general public. The joint compound does not cover fasteners. Drywall joints and angles are taped with tape. This can be used in corridors or other areas with pedestrian traffic. Drywall companies can add accessories, while some boards have tool marks or ridges.

Level 2

To protect the joints and interior angles, tape is used to seal the joints. Any excess compound is quickly removed, and a thin layer of compound left over the joints and angles. While the joint compound covers fasteners and accessories, you can still see tool marks as well as ridges. When a tile substrate is made of a water-resistant board, Level 2 drywall finishes are often used.

Level 3

Level 3 finishes are similar to level 2. The tape is embedded in joint compound, and then wiped to create a thin coating over the joints and interior angles. This is because a second layer of joint compound is applied to the joints and interior angles. Fasteners and accessories are also covered with this extra coating. This does not leave any tool marks or ridges. After the surface has been prepared, it's finished with a primer for drywall before the final decoration.

When heavy wall decorations and drywall repair Denver textures are to be applied last, Level 3 drywall finishes is recommended. This is not the right finish for residential painting and lightweight wallcoverings.

Level 4

These are the same steps as before. The interior angles and joints are taped with joint compound. After that, the area must be cleaned to remove any excess coating. The difference is that the contractor will apply two coats of joint compound to the flat joints, and one to the interior angles. Contractors apply three coats over accessories and fasteners. All joint compounds are smoothened and will not leave any tool marks or ridges. The contractor will finish the surface with a primer before you can decorate it as you wish.

This is the recommended drywall finish for residential wallcoverings of light colors, textures, and flat paints. It is important to conceal all fasteners and joints, so they don't show underneath the flat or glossy paint, or any other wallcoverings.

Level 5

This is the highest grade of drywall finish. It ensures uniformity and conceals all imperfections. Tape is still embedded in the joint compound at the joints and interior angles. This tape is quickly removed to make a thin coating. Two separate coats of compound are then applied to the flat joints, and one to the interior angles. For better results, accessories and fasteners are covered with three coats. The entire surface is then finished with a skim coat joint compound. This seals in the smoothness and conceals any imperfections. There are no tool marks and ridges.

A primer is required before drywall can be decorated. A good preparation of drywall will ensure that fasteners are not visible. The smooth surface can be used for flat, semi-gloss or gloss paints. Because level 5 drywall finishes hide all imperfections, they are ideal for situations where the wall angle and lighting may show flaws.

To sum up. You need a smooth, flat surface that is free from imperfections if you plan to use flat or glossy paints. This is level 5. The higher the level, the better. If you choose texturized commercial paint, you don’t have to pay for level 5, but if your preference is flat paint, you should.

 

drywall Denver

 

drywall repair Denver

 

Denver drywall

 

Denver drywall company

 

drywall contractor Denver

 

drywall contractors Denver

 

drywall installation Denver

 

Denver drywall contractors

 

drywall finishing Denver

 

drywallers Denver

 

drywall repair Denver CO

 

drywall contractors Denver CO

 

drywall companies in Denver Colorado

 

drywall contractors Denver Colorado